We have a great sale going on right now
for new customers. Book a detail for 99¢! *
CONTACT US
Johnny Detail. Boat detailing. Six care chapters introduce material-specific cleaning and conditional finish decisions.
Prepare before the first rinse. Clear gear and contain contaminated runoff. Loose deck gear is staged away from the work area. The supported boat, stable access and runoff containment establish preparation before water flows.
Rinse salt from top to bottom. Use gentle freshwater around seams and electronics. A restrained freshwater rinse follows exposed upper boat surfaces downward, avoiding electronics, hatch seals and concentrated jets.
Treat remaining salt selectively. Choose a compatible marine product as needed. A label-check cue precedes targeted salt treatment on remaining deposits. Soft agitation and complete rinsing follow the approved product directions.
Inspect the revealed finish. Record stains and oxidation before contact washing. An inspection light follows the waterline and hull; a condition record distinguishes staining, oxidation and repair concerns before the next task.
Identify and target the stain. Use labelled products on approved finishes. A small waterline stain is isolated for finish-compatible treatment. The film shows label checking, gentle application and contained rinsing, without an acid recipe.
Wash, rinse and dry. Keep clean wash tools separate from dirty areas. Marine wash solution and a clean soft mitt lift hull film in small sections; freshwater rinsing and clean towels reveal the dry finish.
Correct oxidation only when needed. Test a small compatible finish section first. An inspection lamp compares a bounded gelcoat test area before a limited correction pass. Clean pads, continued movement and reassessment are emphasized.
Choose compatible finish protection. Follow the selected system’s preparation and cure. Separate wax, sealant and coating options illustrate a selected compatible protection system on prepared smooth hull finish. Cure requirements come from that product.
Prepare the walking surfaces. Lift loose salt and dirt before brushing. Gentle rinsing removes loose debris from non-skid texture while a separate smooth topside panel establishes distinct material zones.
Match cleaner to deck material. Non-skid, gelcoat and teak need distinct care. An approved deck cleaner works a small textured section; a material record distinguishes it from smooth gelcoat and any actual teak surface.
Brush the texture gently. Rinse tools before dirt returns to clean areas. A suitable brush follows non-skid grooves in controlled passes without excessive abrasion. Smooth glossy edges remain outside the textured-deck brush path.
Remove residue and preserve grip. Dry fully; use only approved deck treatment. Freshwater clears cleaner from the deck and towels dry walking areas. Any optional treatment remains material-approved and conditional, preserving traction.
Separate vinyl from canvas. Brush loose dirt before wet cleaning. A vinyl bench and actual canvas panel occupy separate care stations. Loose debris is removed with soft tools before either receives cleaner.
Treat stains with material approval. Address dampness that lets mildew return. A small stain receives only a material-approved product. A moisture-source record accompanies the treatment instead of showing indiscriminate household bleach.
Clean each material separately. Use soft tools and complete residue removal. A soft brush follows the vinyl seam, while the separate canvas receives its own fabric-specific cleaning method. Tools and products stay distinct.
Dry before storage. Keep airflow moving around clean soft goods. Airflow crosses the separately staged canvas and cleaned vinyl. Inspection checks seams, residue and full drying before storage or permitted material protection.
Identify the metal first. Coated and bare finishes need different methods. A stainless rail, cleat and separate aluminum fitting are inspected and cleaned. Coated and unknown finishes remain outside the polish path.
Clean before cosmetic polishing. Remove salt and grit with dedicated tools. A fresh cloth lifts remaining dirt from accessible bright hardware before polish. Separate tools prevent metal residue transferring to vinyl or hull finish.
Polish only compatible brightwork. Work locally with an approved metal product. A small applicator works a confirmed compatible rail section while neighboring surfaces are protected. No structural fittings are removed.
Buff, inspect and record. Clean shine does not repair corrosion. A fresh towel removes polish residue. Inspection leaves existing pitting visible and records concerns rather than hiding them beneath a glossy finish.
Protect sensitive equipment. Use exterior wiping around closed electronics. The closed helm electronics housing is wiped gently while nearby access limits are recorded. Cosmetic care remains separate from electrical servicing.
Empty accessible compartments. Clean and dry storage before replacing belongings. Loose gear is removed from an accessible locker. A compatible cloth cleans the interior without flooding hidden spaces.
Handle bilge waste responsibly. Stop for fuel concerns; collect contaminated water. An inspection record identifies contaminated standing water. Absorbent pads and an appropriate waste container illustrate collection; no ordinary vacuum or routine discharge pump is activated.
Dry, reassemble and inspect. Leave compartments residue-free and electronics dry. Fresh towels clean approved accessible hard surfaces. Dry gear returns to its locker and the final condition record remains visible, with electrical boundaries unchanged.
Inspect. Document. Explain.. Check clean, dry surfaces and record remaining concerns.
Care matched to your vehicle. Included work depends on package, condition and material approval.
Read the complete checklist. /guides/boat-detailing Johnny Detail. /guides/boat-detailing.
For a Pasadena boat request, start with length, support and photographs of the hull and topsides. Point out places obscured by bunks, covers or adjacent storage. A trailered vessel and one at a dock present different working positions; the scope should reflect that arrangement.
Paint and gelcoat can look alike in photographs, while clear enclosures, metal and upholstery need different products again. Tell us about previous protection and areas that appear oxidized. Refinement is condition-dependent work, distinct from routine cleaning, and cannot repair cracks or failed surface layers.
Provide the operator’s access requirements if the boat is stored off-site. Pasadena’s Armand Bayou recreation context is not evidence that cleaning a powered vessel is permitted at a public access location. Agree property permission, available working space and reachable areas before arranging equipment or moving the boat.
Compare existing boat packages and ask specifically about the hull, seating, covers and any heavier polishing. Obtain aftercare suited to the confirmed materials. Haul-out, underwater surfaces, structural repairs and mechanical service require their own scope. A cleaner vessel still needs normal inspection and maintenance for its use.
Send the hull, topsides, seating and problem areas, plus views showing supports and working clearance. Include vessel length and finish information.
It should not be assumed. Reachable cosmetic surfaces and any haul-out or underwater requirements must be discussed as separate scope questions.
No. Cracks and structural surface damage require suitable repair. Refinement can only improve a finish within its existing limits.
Yes, confirm the relevant property rules and access permission. A boat’s presence in storage does not itself authorize service activity.
No. Upholstery, textured decks and hull finishes need compatible care selected for each material and its function.
Please note that a $18.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $35.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $55.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $28.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $55.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $85.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $20.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $55.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $94.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $25.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $70.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Please note that a $120.00 deposit (10% of the service total) is required to reserve your appointment, and is applied toward your final balance.
Plan your next detail
Tell us what you drive, how you use it, and where you would like your mobile appointment.
Learn to clean, dry, and retreat bimini canvas with fabric-specific products, careful rinsing, ventilation, and checks for seams or coating wear.
Read the guide
Compare teak oil and sealers for saltwater decks, including appearance, traction, compatibility, surface preparation, and ongoing upkeep.
Read the guide
Plan cautious hull-film and barnacle removal with gelcoat checks, marine-compatible tools, runoff awareness, and guidance on when to call a boatyard.
Read the guide
